Used Dental Laser Dentistry | Biolase ezLase 940 ( 1465) | Atlas Resell Management

You are here

Used Dental Laser Dentistry | Biolase ezLase 940 ( 1465)

The ezlase™ Dental Soft Tissue Laser is a surgical device at the cutting edge of technology, designed for a wide variety of oral soft tissue procedures. The ezlase™ 940 diode laser utilizes a solid state diode as a semiconductor source of invisible infrared radiation. The energy is delivered to the treatment site via flexible fiber, connected at one end to the laser source and the other end to the handpiece. Various types of the single use tips were designed and optimized for different applications. The device is activated by means of a footswitch.

The ezlase is also an ideal teeth-whitening tool. A full-mouth, in-office whitening can be performed in only 20 minutes.

Features: 
  • 940 nm wavelength
  • ComfortPulse™ 
  • Has battery pack 
  • Has standby” and “ready mode” functions
  • Uses bendable tips for better access to all areas
  • Offers precise control of tissue cutting for different procedures and tissue biotypes
  • BIOLASE’s proprietary TCIA™ 20-minute Laser teeth-whitening tool
  • Exclusive beam-dispersing handpiece
Benefits: 
  • Cuts efficiently at lower power and with less heat
  • Reduce the amount of time the laser cutting
  • Avoid pain-inducing heat build-up at the surgical site
  • Can perform ezlase procedures using topical anesthetic only
  • Allows positioning of device for optimal operating convenience
  • Easy transport between operatories
  • Guard against unintentional delivery of laser energy
  • Offers single-use disposable tips for quick, convenient treatment, and improved cleanliness
  • Temporary pain therapy and relief
Limitations/Considerations: 
  • Do not operate in the presence of explosive or flammable materials. Flammable anesthetics or oxidizing gases such as nitrous oxide and oxygen should be avoided. Solvents of adhesives and flammable solutions used for cleaning and disinfecting should be allowed to evaporate before laser is used. Attention should also be drawn to the danger of ignition of endogenous gases.
  • Do not look directly into the beam or at specular reflections.
  • Always be aware of adjacent structures and substructures during treatments. Be extremely careful not to inadvertently penetrate or ablate underlying or adjacent tissues. Do not direct energy towards hard tissues such as tooth or bone. Exercise extreme caution when using this device in areas such as pockets, 31 cavities or channels such as 3rd molar sockets, where critical structures (i.e. nerves, vessels) could be damaged. Do not proceed with using the laser if visibility is limited. Do not direct energy towards amalgam, gold or other metallic surfaces. Do not direct energy towards cements or other filling materials.
Technical Specifications: 
  • Dimensions ( W x L x H ) :: 
    (3.5” x 7.0” x 2.5”) (8.5 x 18 x 6cm)
  • Weight: 
    2 lbs
  • ELECTRICAL : Operating Voltage: 
    100 to 240 ~ at 2A
  • Frequency: 
    50 / 60 Hz
  • External Fuses: 
    None
  • Main Control: 
    Power Switch
  • On / Off Controls: 
    Keypad Button, Emergency Stop
  • Remote Interruption: 
    Remote Interlock Connector
  • Laser Classification: 
    IV (4)
  • Medium: 
    GaAlAs, InGaAsP
  • Wavelength: 
    810 ± 15 nm or 940 ± 15 nm
  • Max Output Power: 
    7 Watts @ 940nm, 4.5 Watts @ 810nm
  • Power Accuracy: 
    ± 20%
  • Power Modes: 
    Continuous, Pulse Modulation
  • Pulse Length*: 
    0.06 ms - 10 sec
  • Pulse Interval*: 
    0.06 ms - 10 sec
  • Pulse Repetition Rate: 
    up to 10 KHz (for reference)
  • Fiber Tips Diameter: 
    200, 300, 400 µm
  • NOHD: 
    11.8 meters
  • Beam Divergence: 
    8 – 22 degrees per side angle
  • Fiber Cable Length: 
    5 feet (1.524 meters)
  • Aiming Beam: 
    Laser Diode, max 3 mW, 630-670nm, class 3B